[BETA] Diskuzní fórum Elektro Bastlírny

AB1 píše:http://www.nongnu.org/avrdude/user-manu ... ude_6.html

Tady máš příklady příkazů, tak to piš přesně podle nich.

ale tam jsou ty začátky příkazů uplně jiné, než jsi mi sm napsal ty. Když jsem jenou upravil tu "příponu" která tam je navíz od 1. příkazu, stane se toto:

Microsoft Windows [Verze 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. Všechna práva vyhrazena.

C:\Users\DAVID>Desktop\x64\avrdude -c avrisp -P com3 -b 19200 -p t45 -U flash:w:
roborizeh.hex

avrdude: please define PAGEL and BS2 signals in the configuration file for part
ATtiny45
avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.13s

avrdude: Device signature = 0x1e9206
avrdude: NOTE: FLASH memory has been specified, an erase cycle will be performed

To disable this feature, specify the -D option.
avrdude: erasing chip
avrdude: please define PAGEL and BS2 signals in the configuration file for part
ATtiny45
avrdude: reading input file "roborizeh.hex"
avrdude: error opening roborizeh.hex: No such file or directory
avrdude: input file roborizeh.hex auto detected as invalid format
avrdude: can't open input file roborizeh.hex: No such file or directory
avrdude: read from file 'roborizeh.hex' failed

avrdude: safemode: Fuses OK

avrdude done. Thank you.


C:\Users\DAVID>

To znamená, že je to OK? nebo ne

tam je stále chyba v tom hex souboru, ne? zkusím z něj udělat nový


dodatek: tak udělání nového souboru z tamtoho nic neudělalo, je to to samé

nakopíruj roborizeh.hex do adresáře avrdude a zachovej avrdude -c avrisp -P com3 -b 19200 -p t45 -U flash:w:roborizeh.hex

pavoucisit píše:nakopíruj roborizeh.hex do adresáře avrdude a zachovej avrdude -c avrisp -P com3 -b 19200 -p t45 -U flash:w:roborizeh.hex

a je to tu zase

Microsoft Windows [Verze 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. Všechna práva vyhrazena.

C:\Users\DAVID>
C:\Users\DAVID>
C:\Users\DAVID>Desktop\x64\avrdude -c avrisp -P com3 -b 19200 -p t45 -U flash:w:
roborizeh.hex

avrdude: please define PAGEL and BS2 signals in the configuration file for part
ATtiny45
avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.13s

avrdude: Device signature = 0x1e9206
avrdude: NOTE: FLASH memory has been specified, an erase cycle will be performed

To disable this feature, specify the -D option.
avrdude: erasing chip
avrdude: please define PAGEL and BS2 signals in the configuration file for part
ATtiny45
avrdude: reading input file "roborizeh.hex"
avrdude: error opening roborizeh.hex: No such file or directory
avrdude: input file roborizeh.hex auto detected as invalid format
avrdude: can't open input file roborizeh.hex: No such file or directory
avrdude: read from file 'roborizeh.hex' failed

avrdude: safemode: Fuses OK

avrdude done. Thank you.


C:\Users\DAVID>

roborizeh.hex ještě nakopíruj přímo na C:

co když avrdude bere C: jako kořenový adresář

pavoucisit píše:roborizeh.hex ještě nakopíruj přímo na C:

avrdude bere C: jako kořenový adresář

opět toto

Microsoft Windows [Verze 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. Všechna práva vyhrazena.

C:\Users\DAVID>Desktop\x64\avrdude -c avrisp -P com3 -b 19200 -p t45 -U flash:w:
roborizeh.hex

avrdude: please define PAGEL and BS2 signals in the configuration file for part
ATtiny45
avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.11s

avrdude: Device signature = 0x1e9206
avrdude: NOTE: FLASH memory has been specified, an erase cycle will be performed

To disable this feature, specify the -D option.
avrdude: erasing chip
avrdude: please define PAGEL and BS2 signals in the configuration file for part
ATtiny45
avrdude: reading input file "roborizeh.hex"
avrdude: error opening roborizeh.hex: No such file or directory
avrdude: input file roborizeh.hex auto detected as invalid format
avrdude: can't open input file roborizeh.hex: No such file or directory
avrdude: read from file 'roborizeh.hex' failed

avrdude: safemode: Fuses OK

avrdude done. Thank you.


C:\Users\DAVID>

Já opravdu nevím, v čem je chyba

Cele zle... Spustas to v "C:\Users\DAVID", tak tam musi byt aj ten hex subor!

Soubor hex může být kdekoliv, ale zkus za něho napsat ještě :i

AB1 píše:Soubor hex může být kdekoliv, ale zkus za něho napsat ještě :i

Kód: Vybrat vše

avrdude -c avrisp -P com3 -b 19200 -p t45 -U flash:w:"C:\Users\DAVID\Desktop\roborizeh\roborizeh.hex":i

Jooo! Teď to s tim "i" už vyšlo (teda myslim)

Microsoft Windows [Verze 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. Všechna práva vyhrazena.

C:\Users\DAVID>Desktop\x64\avrdude -c avrisp -P com3 -b 19200 -p t45 -U flash:w:
"C:\Users\DAVID\Desktop\roborizeh\roborizeh.hex":i

avrdude: please define PAGEL and BS2 signals in the configuration file for part
ATtiny45
avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.07s

avrdude: Device signature = 0x1e9206
avrdude: NOTE: FLASH memory has been specified, an erase cycle will be performed

To disable this feature, specify the -D option.
avrdude: erasing chip
avrdude: please define PAGEL and BS2 signals in the configuration file for part
ATtiny45
avrdude: reading input file "C:\Users\DAVID\Desktop\roborizeh\roborizeh.hex"
avrdude: writing flash (890 bytes):

Writing | ################################################## | 100% 1.49s

avrdude: 890 bytes of flash written
avrdude: verifying flash memory against C:\Users\DAVID\Desktop\roborizeh\roboriz
eh.hex:
avrdude: load data flash data from input file C:\Users\DAVID\Desktop\roborizeh\r
oborizeh.hex:
avrdude: input file C:\Users\DAVID\Desktop\roborizeh\roborizeh.hex contains 890
bytes
avrdude: reading on-chip flash data:

Reading | ################################################## | 100% 1.09s

avrdude: verifying ...
avrdude: 890 bytes of flash verified

avrdude: safemode: Fuses OK

avrdude done. Thank you.


C:\Users\DAVID>


Díky všem za rady!

zdravim potrebuju poradit s nahranim bootloaderu pise mi to
avrdude: Yikes! Invalid device signature.
Double check connections and try again, or use -F to override
this check.

lodtom24 píše:zdravim potrebuju poradit s nahranim bootloaderu pise mi to
avrdude: Yikes! Invalid device signature.
Double check connections and try again, or use -F to override
this check.

Přes co to programuješ a čím. Dej sem popřípadě printscreen

no pres arduino IDE kdyz sem mel klasickej velkej atmel ten sem nahral bezproblemu

a programuju to normalne zas tim velkym atmelem kterej normalne pouzivam kamos ma nanov3.0 taky dosel jen k tomuhle hlaseni chyby

klasickej velkej atmel

Tento typ jsem v katalogu nenašel.

atmega328p-pu je normalne v arduinu uno ten pouzivam ten sem bez problemu nahral a ted mam tohle a pise to neco o prepsani -f chci to nahrat na tento

http://www.ebay.com/itm/151253230478?ss ... 1497.l2649